Problem installing hard drive on Dragon+

mritz · Post by **mritz** » Sat Jan 19, 2002 10:52 pm

I just received my replacement hard drive from Maxtor and trying to get
it to install with no luck at all

I have a Dragon + And Athlon 1700+ XP Windows XP
I have my CD and DVD set on IDE 1 (set Master/Slave)
CDRW on IDE 2 (master)
Boot drive is a WD 20g on IDE 3 works good set for( MASTER)
Storage drive is a Maxtor 6L080L4 80g ATA133 7200rpmIDE4 (master)
The 80g drive detects in the Promise Bios just fine Windows XP finds the drive
and trys to install it but keeps telling me it could not install the drive

An error occured durring the instalation of this device
one of the filter drivers installed for this device is invaild

If I look in device manager it shows the drive yellowed out but I can go to
My Computer or Explorer and read and write to the drive ??
I had a 30G Maxtor installed and pulled it to install the 80g and the 30g
worked fine I have tried everything I can think of with no luck

bigcfromcinci · Post by **bigcfromcinci** » Sat Jan 19, 2002 11:46 pm

Mark,
Have you tried it in another rig by any chance??

mritz · Post by **mritz** » Sun Jan 20, 2002 8:05 am

No I have not tried it in another system yet
I will try it in my wife's later today and see if it will detect there

outfits · Post by **outfits** » Fri Jan 25, 2002 12:49 am

If its your only device on that channel remove the jumper.
Just remenbered I did hear about some "problems with > 80gb drives" but don't recall the fix. Google might turn up something for ya.

dadx2mj · Post by **dadx2mj** » Fri Jan 25, 2002 1:25 am

I have a 10gig Maxtor that I had problems with on my Dragon. I had it hooked up to the 2sd IDE prot and it would detect but I could not read from it or write to it. Turned out I had to have the jumper set to "Cable Select" for it to work. Not your exact problem but maybe it will help.

mritz · Post by **mritz** » Sun Jan 27, 2002 7:26 am

Well I tried everything I could think of and then some

I even started having the same problem with my Boot Drive(20g W/D)
after moving things around
I finaly did a full install of XP and the drives are installed BUT if I move either of my
hard drives I end up with the same problem all over ?
I tried setting them a Master and Cable select with NO change
this is a very weird problem to say the least
I can move my CD rom DVD or CDRW with NO problems redetecting and installing
I only have problems with the hard drives

chottoED · Post by **chottoED** » Sun Jan 27, 2002 11:52 am

just wondering...
are you using the winXP built in promise drivers? or the latest ones...
also do you have the latest BIOS flash...

mritz · Post by **mritz** » Sun Jan 27, 2002 12:56 pm

Have not updated the Bios from what was in when I received the board from
Newegg I have installed the newest Promise Drivers...If I move my drives from IDE3 &4 to
IDE 1 and 2 I will have the same problem so it is not a problem
with the promise controler

I did a fresh install of XP I had the drives connected as follows
IDE 1 W/D 20 g Boot
IDE 2 Maxtor 80g
IDE 3 CD rom & DVD
IDE 4 CDRW\

With fresh install all drives were detected and installed but my CDRW software could not find
my cdrw on IDE 4 so no problem I would switch them
IDE 1 CD & DVD
IDE 2 CDRW
IDE 3 Boot W/D 20g
IDE 4 80g Maxtor

After moving them All the CD drives were detected and installed just fine BUT My W/D and
Maxtor were not installing

now both Hard drives were giving the same error
So after a couple days of screwing with it I finaly reinstalled XP AGAIN
after fresh install EVERYTHING detected and installed and as of right now they are working
but I have to have something wrong here if I can not move a hard drive with out
having problems reinstalling it

chottoED · Post by **chottoED** » Sun Jan 27, 2002 1:06 pm

give this a shot
http://www.soyo.com.tw/cgi-bin/prodinfo ... GON&bios=1

VidmanII · Post by **VidmanII** » Mon Jan 28, 2002 11:44 am

First thing I'd do is check the IDE cables. Might be the prob. That happened to me. If you move the HDDs to a different channel, do it with all other devices ( opticals ) disconnected. Just the bare minimum initially. If you already did this stuff just disregard.

Not for nuthin' but if it's a new install ( fresh OS etc) , you may be better off getting it up and running on the standard IDE controller ( RAID controller disabled ) first and then once you have the OS, drivers, updates loaded then shutdown, switch it over to RAID controller which of course you would enable at this point and see if it works. That's provided your HDD is able to be detected. I always did it that way with my Iwill KK266's and it worked like a charm. That was with a Hpt370 RAID controller tho so I can't speak for the Promise thingy.

BTW, too bad about those PITT Steelers eh?

muwahahaha

GO Browns !!